-
Υπερήχων ανιχνευτής ελαττωμάτων
-
υπερηχητικός μετρητής πάχους
-
Μετρητής πάχους επιστρώματος
-
φορητός ελεγκτής σκληρότητας
-
των ακτίνων X ανιχνευτής ρωγμών
-
Χημικά οχήματα για τη διάταξη σωλήνων ακτίνων Χ
-
Ανιχνευτής διακοπών
-
μαγνητική δοκιμή μορίων
-
Τρέχων εξοπλισμός δοκιμής του Eddy
-
Δοκιμές διεισδυτικών ουσιών
-
Δυομετρητής ακτής
-
brinell ελεγκτής σκληρότητας
-
rockwell ελεγκτής σκληρότητας
-
Ελεγκτής σκληρότητας Vickers μικροϋπολογιστών
-
Δοκιμαστής σκληρότητας υλικού
-
μετρητής δόνησης
-
Δοκιμαστής τραχύτητας επιφάνειας
-
Προβολέας Προφίλ
-
Μετρήσεις λάμψης
-
συγκεκριμένο σφυρί δοκιμής
-
Θερμόμετρος υπερύθρων λέιζερ
-
ΒαρίδιΤύπος 1018 χάλυβας άνθρακα φραγμών δοκιμής βαθμολόγησης μίνι Iiw 2 ίντσας Astm E114-15
-
ΓουλιέλμοςΤύπος 1018 χάλυβας άνθρακα φραγμών δοκιμής βαθμολόγησης μίνι Iiw 2 ίντσας Astm E114-15
-
ΚάποιοςΤύπος 1018 χάλυβας άνθρακα φραγμών δοκιμής βαθμολόγησης μίνι Iiw 2 ίντσας Astm E114-15
-
LeoΤύπος 1018 χάλυβας άνθρακα φραγμών δοκιμής βαθμολόγησης μίνι Iiw 2 ίντσας Astm E114-15
Dual Element Phased Array Probes For Ultrasonic Inspection Equipment ISO CE

Επικοινωνήστε μαζί μου για δωρεάν δείγματα και κουπόνια.
Το WhatsApp:0086 18588475571
Βυθός: 0086 18588475571
Skype: sales10@aixton.com
Αν έχετε οποιοδήποτε πρόβλημα, παρέχουμε 24ωρη ηλεκτρονική βοήθεια.
xΠεδίο συχνότητας | 12από 0,5 MHz έως 10 MHz | Μετατροπέας επαφής | διαφόρων μεγεθών στοιχείων |
---|---|---|---|
Προστατευμένος μετατροπέας προσώπου | με φιλμ ή παπούτσια | Μετατροπέας δύο στοιχείων | Διπλό στοιχείο |
Κλινοειδής σφήνα | ΑΕΠ ΑΕΠ ΑΕΠ ΑΕΠ | Υλικό | πλαστικό, αλουμίνιο, κράμα |
Επισημαίνω | ultrasonic flaw detectors,ultrasonic flaw detection,digital ultrasonic flaw detector |
Ultrasonic ndt equipment Ultrasonic Inspection Equipment Probe Transducer Phased Array Prob
1. Straight probe: single crystal p-wave straight probe double crystal p-wave straight probe
2. The Angle probe: single crystal shear Angle probe a1 < aL < a Ⅱ, twin shear Angle probe
Single-crystal p-wave oblique probe aL
AL is a climbing wave probe near a1. The longitudinal wave transmitted along the surface of the workpiece has the advantages of fast speed, high energy, long wavelength, deeper detection depth than the surface wave, and the requirement for the surface finish of the workpiece is higher than that of the surface wave (frequency 2.5mhz wavelength about 2.4mm).
3. Probe with curvature: circumferential curvature, radial curvature.
The circumferential curvature probe is suitable for the detection of axial defects in seamless steel tubes, straight welded tubes, tubular forgings and axial workpieces. When the diameter of the workpiece is less than 2000mm, the circumferential curvature of the probe shall be ground to ensure good coupling.
Radial curvature probe is suitable for the detection of radial defects in seamless steel pipe, butt weld of steel pipe, barrel forging, shaft workpiece, etc. When the workpiece diameter is less than 600mm, the radial curvature of the probe should be ground to ensure good coupling.
4. Focusing probe: point focusing line focusing.
5. Surface wave probe :(when the incident Angle of the longitudinal wave is greater than or equal to the second critical Angle, the transverse wave refraction Angle is equal to 90 to form a surface wave).
The transverse wave transmitted along the workpiece surface has a slow speed, low energy and short wavelength, and the detection depth is shallower than the crawling wave. Therefore, the requirements for the surface finish of the workpiece are stricter than the crawling wave.
Surface wave detection can only detect defects at a depth of two wavelengths from the surface of the workpiece. (frequency 2.5mhz wavelength about 1.3mm).